How to Install Springwell Water System? Complete Guide

Last updated on January 2nd, 2024

The installation of Springwell water filtration systems is not difficult to do. Springwell water filtration systems are not pre-assembled, in contrast to other forms of water filtration systems. If you have some experience with tools, you should have no trouble learning; how to install the Springwell water system.

If you are new to handling tools, we recommend hiring a professional contractor who, in many circumstances, will be able to manage any plumbing concerns that arise along the route.

How to install Springwell water system?

The Carbon Tank Head Installation 

Usually, the tank head is placed first. A tank head and a carbon filter are required. These can be done remotely. Remove the CO2 tank cap. Find the tank’s head. The tank’s top has a pipe that must be aligned with the tank’s entrance.

Adjust the tank head to the tank and press it in place. Tighten the tank head using a screwdriver.

Pre-soaking the Water Filtration System Tank

The carbon must be soaked in the tank for at least 48 hours before use. These parts will be needed: a set of bypass valves, an empty carbon tank, the two MNPT fittings, an outdoor faucet, and an accessory kit. The bypass valve should be attached to the tank head. The valves’ fasteners need to be tightened.

Attach the MNPT fittings to each bypass valve connection. To allow water to flow through the system, you must turn off the bypass valve and connect a lawn hose pipe connected with a hose bib to the pipe (inlet). 

Flushing the carbon tank

To flush the tank, you’ll need a hose bib installation, a carbon tank, and a yard hose. Connect the water hose and hose bib assembly to the tank’s inlet. Turn off the bypass switch. Presoaking will cause some of the water to leak out. Using water to flush it out is the most common method. Please be mindful that the water will initially seem to be a dark shade of brown. For the next 5 minutes, it should become evident.

Flush in the opposite direction as well. Allow water to flow for five minutes after flipping your hose bib and water hose. Disconnect the pipe and fittings. Make sure you zip up the jacket gradually before putting it on the tank top.

Sediment Filter Installation

For the installation, you’ll need a drill bit and three PVC Nipples, each measuring 1 inch (3 centimetres). An intake and an outlet are provided on the sediment filter housing. The PVC nipples should be attached to both inlets. The plumber’s tape should be used to seal the gap.

Install the sediment filter so that the carbon tank is in line with it. Affix the mounting rack to the wall with a 3′′ drill bit. Before installing the sediment filter with bolts, make sure the inlet and outlet are in the correct position.

Adding a Shut-Off Valve to the System

Water Filtration Tanks for the Whole Home

Carbon tanks should be placed directly in front of the sediment filter. Whenever possible, wires and connections should be oriented in the reverse direction. Connect the corrugated pipes to the carbon tank’s shut-off valve inlet. The carbon tank’s output must be connected in the same way as the carbon tank’s inlet.

The corrugated pipe from the carbon tank to the sediment tank’s nook should be attached in the similar way. Connect a second corrugated pipe from the sediment tank outlet to the home water line from the opposite side of the tank. To avoid leaks, be sure that all of your connections are snugly fastened.

• Make sure the Water Filtration System is working properly

• Whether or not the sediment filter housing is securely fastened in place.
• Open any faucet in your house while the water supply is still shut off to allow water to flow.
• Check to see if the shut-off valve is leaking, and then move forward to the subsequent step.
• Check the bypass valves for leaks before turning the water back on.
• For a minimum 5 minutes, let the water flow through the systems. Water will be pure and free of silt if this procedure is followed.

Read Also: Springwell vs Pelican

How to change the Springwell water filter?

• Remove pressure from the system by closing all inlet and exit valves.
• To collect the water, place a bucket under the filter housing.
• Remove the bowl by unscrewing it counterclockwise with a filter wrench (to the left).
• Recycle the empty cartridge. The filter container should be emptied into the bucket.
• Remove the O-rings and clean them of any lubrication. Set aside for further investigation. Replace or discard the broken O-ring.
• Add 1 tbsp (30 ml) bleach to the 1/3-filled bowl. Using a non-abrasive sponge or towel, scrub thoroughly to remove any buildup of bacterial, rust, and scale particles, and then rinse thoroughly
• Make sure the O-ring grooved sitting area is clean.
• Remove the cartridge’s protective wrapping and set it in the bowl with the post fitted over it.
• Place the O-ring in the groove after it has been lubricated with petroleum jelly. Take a look at the O-ring and ensure that it is installed evenly and at point.
• Using a screwdriver, tighten the bowl clockwise until the cartridge is aligned with the post in the filter head. It’s important not to overtighten the screws.
• As water fills the housing, press the red pressure-relief button and hold it down while slowly opening the inlet valve until water flows out of the relief button. Repeat as necessary. To remove any remaining air from the line, softly open the outlet valve.
• Before using, run a few cycles of water through the system.
• Make sure there aren’t any leaks.

How to install Springwell water softener?

Water softener installation

• Turn off the water at your house.
• Install shut-off valves on both ends of your main water supply line.
• To supply the water softener, use PVC nipples and corrugated pipes.
• Remove the blue tab that is attached to the drain valve by unscrewing it from its socket.
• The drain valve should then be removed.
• Drain line: Slide the hose clamp over the line.
• Make sure the drain line is connected to the drain valve’s barbed end with the help of a hose. Tighten with a clamp.
• Lock the drain valve in place with the blue tab.
• Make that the other end of the drain line is attached to the drain.
• The filter wrench can be used to tighten the pre-filter housing.
• Connect the electronic head’s power cord.
• Locate the battery connection by removing the headcover.

Brine tank installation

1. The drain line should be connected to the brine tank’s barbed valve. The other person can follow your lead to the sink.
2. Make sure that you open the brine tank and remove its cap.
3. Connect the regen line to the brine well through the brine tank hole.
4. Replace the brine well cover and add salt to it.
5. Close the tank lid.

Read Also: Filtersmart Vs Springwell

System Testing

1. Turn on all of the faucets at once.
2. Set the water softener bypass and the shut-off valves to off.
3. To begin, turn on the water supply in your home.
4. Check the incoming water supply shut-off valve for leakage.
5. Check the water softener bypass for leaks by opening the shut-off valve.
6. Open the bypass and let the system run for five to ten minutes to clear any accumulated waste.
7. After then, it’s time to dial in the softer settings!

FAQ: How to install Springwell water system

Can you install a water softener system yourself?

To save money and time, you can install a water softener on your own by following our step-by-step instructions. A new water softener may be installed in under an hour if the old one needs to be replaced.

Do I need to soak my water filter?

Before using them for the first time, water filters should be soaked for around 15 minutes. The water filter should be rinsed 2-3 times with running water after soaking to eliminate any stray particles, including carbon dust. All water filters should be pre-soaked for at least 10-15 minutes, however, this can vary by brand.

Final Thoughts: How to install Springwell water system

Many people utilize Springwell whole-house water filters as an option. The Springwell water filtration system should be installed by a professional. That way, the water system’s pressure and flow rate may be considered during installation.

The fact that this system requires so little upkeep is a huge plus. Depending on the water quality, the user will need to inspect the sediment filter regularly.